POWERSHAPE™ PS-2.1Class D Amplifier with DSPUser Manual Version 1.211/19/2013DIGITAL AUDIO LABS - 1266 Park Road - Chanhassen, MN 55317support@digital
BLOCK DIAGRAM 10
INPUT CONFIGURATIONThe PowerShape 2.1 offers both stereo analog and stereo digital inputs. •Analog Input -10dBV (RCA style connectors)•Digital Input (
OUTPUT CONFIGURATIONThe PowerShape 2.1 provides Left, Right and Sub speaker level, terminal block outputs. A wide range of volume and processing contr
STEREO ENHANCEMENTA stereo enhancement features is available on the master output. Use this control to increase the stereo image of your system when s
CONTROL AND SETUP OPTIONSThe PowerShape 2.1 offers several control options including USB, RS-232, Ethernet and Infrared. If this is your first time usi
SOFTWARE CONFIGURATIONThe PowerShape 2.1 configuration software provides real time control of all audio and control parameters. Most editable parameter
SERIAL (RS-232) CONFIGURATIONAdditional serial port configuration settings are located within the Communication section of the menu bar. Serial setting
USER MAINTENANCEENVIRONMENTAL CONSIDERATIONSThe biggest factor in the lifetime of any electronic device is excess heat. The PowerShape 2.1 is designed
WARRANTY AND SERVICEDIGITAL AUDIO LABS LIMITED WARRANTYDigital Audio Labs warrants their products against defects in material and workmanship for a pe
TECHNICAL SPECIFICATIONSPOWERSHAPE™ PS-2.1ParameterSpecificationNotesSpeaker OutputsFrequency Response20Hz to 20kHz+0, -3dBDynamic Range>90 dBA-weig
This page intentionally left blank2
APPENDIXPROGRAMMER’S GUIDEThe PowerShape 2.1 amplifier can be remotely operated by control and automation systems, such as those manufactured by Crest
The network port supports IPv4. The network port's IP address can assigned dynamically by a DHCP or BOOTP server, assigned dynamically using 169.
Program Command / Response ProtocolBoth the serial and network ports use the same command/response protocol. All commands and responses are composed o
Parameter Item NamesVersion and status information. All items in this section are valid only for a get command.get boot firmware version number: verb
Input channel controls.get or set digital input volume: iv0get or set analog input volume: iv1The value indicates the input volume level, in ½ dB step
Output channel controls.get or set output volume: ovThe value indicates the output volume level, in ½ dB steps. The output volume is an integer betwee
get or set output EQ frequency for bass EQ band (low shelving): eqf0get or set output EQ frequency for mid 1 EQ band (peak/dip EQ): eqf1get or set out
get or set output compressor's threshold: cpthrThe value indicates the threshold setting for the output compressor, in ½ dB steps. The threshold
get or set left/right output crossover filter type: xomtypeget or set subwoofer output crossover filter type: xostypeThe value indicates the specified
System / configuration controls.load preset (valid for set only): lprsThe value is the factory or user preset number from which a saved configuration
IMPORTANT SAFETY INSTRUCTIONS! 4WHAT’S IN THE BOX! 5CONNECTIONS! 6FRONT PANEL! 6REAR PANEL! 6INSTALLATION! 7GENERAL INSTRUCTIONS! 8TERMINAL BLOCK WIRI
get or set sleep threshold: sleepthrThe value is the audio level below which the amplifier will be considered “idle”. When idle, the amplifier will be
get or set network port subnet mask: netsubmThe value is the subnet mask to be used when static IP address assignment is selected. The value is a va
get assigned gateway address (valid for get only): netasggwThe value returned is the gateway address assigned to the network port.Example response:=sn
VU meter controls.When enabled, VU reports are sent automatically at approximately the requested rate in the same format as responses to a “get” comma
Quick Reference GuideVersion and status information. All items in this section are valid only for a get command.get boot firmware version number: verb
get or set sleep threshold: sleepthrget or set serial port baud rate: serbaudget or set serial port data format: serfmtget or set network port IP addr
Alphabetic Command Referenceall: get all configuration settingscpatt: get or set output compressor's attack timecpmak: get or set output compress
TROUBLESHOOTINGPROBLEMVERIFY THAT...No PowerAC mains cord is properly inserted into a 100-240VAC receptacle and the external power supply#DC jack (2.1
All specifications subject to change without notification. © Copyright 2013 Digital Audio Labs, All Rights Reserved!! !!!!!!!!!!!38
IMPORTANT SAFETY INSTRUCTIONSWARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.CAUTION: TO REDUC
WHAT’S IN THE BOX1. PowerShape 2.1 - Class D Amplifier with DSP2. Power Supply (24VDC 2.5A)3. IEC Power Cable (6’ Length)4. USB Cable (6’ Length)5. Qui
CONNECTIONSFRONT PANELREAR PANEL 61 - 24VDC Power Input5 - Digital Optical Input (Stereo)2 - Subwoofer Output6 - RS-2323 - Spe
INSTALLATIONThere are two factory presets for quick setup: Conference/Classroom #1 & #2. 7
GENERAL INSTRUCTIONS•Review safety warnings on page 4 before preceding.•Use only the included 24VDC power supply and power cable.•Surge protector or p
TERMINAL BLOCK WIRINGA full set of terminal block connectors is included. General instructions for terminal block connectors:! Strip the wire 1⁄4 inch
Kommentare zu diesen Handbüchern